5 thoughts on “If you are not satisfied with the ring mouth, what method can be used to change its size?”
Orville
Golding method is changed
The gold method is a commonly used ring to change the large -sized method. The specific operation method is to cut the ring ring, add the same precious metal material, and then weld. After the welding is completed, the welding site should be polished and renovated to eliminate welding marks. Although the Gold Method is commonly used, the Gold Method is suitable for some rings with a single trash, no pattern, no more decorative ring.
The gold cutting method to small
The gold cutting method can be changed to small rings size, cut off a short section of the ring, then welded the ring, then polished and refurbished. , Eliminate welding marks. The gold cutting method is also suitable for some rings of the trash, with no pattern and no more decorative ring.
This ring method changes to small
This can also change small size. According to the size of the inner wall of the ring, make a cushion embedded on the inner wall of the ring, and the pads will reduce the ring to reduce the ring. The role of size. The padding method is suitable for all rings to change small size. The padding method has the least harm to the ring. If the ring is small, you can remove the ring of the ring to make the ring larger.
The method of modification of the ring tip of the ring is as follows:
1. The center of the bottom of the ring is sawn, and the ring ring on both sides of the fracture is used to cut the ring on both sides of the fracture. In this way, you can ensure that the two sides of the ring circle are opposite. Is should not cut too much when cutting. After a little cutting, you should use the rings to measure the size of the ring mouth. After cutting, the flap should be slightly larger than the actual need. Use the bamboo leaf cricket to fell smoothly on both sides of the fracture to meet the requirements. At the same time, the smaller the seams at the fracture, the better. 2, take a container, add a little boric acid, and add an appropriate amount of alcohol to completely dissolve boric acid. Put the ring into the boric acid solution. 3, take out the ring in the boric acid solution, use the musket to put the ring hot, and use the tweezers to clamp the sides of the ring ring with the sides of the ring, so that the ring arm on both sides of the ring ring is fitted together. Note: Try to avoid direct heating gems during the heating process. 4. Welded the fracture together to ensure the reliability of welding and avoid forming concave pits, and the amount of welds can be increased in an appropriate amount. 5. After the welding is completed, if it is inlaid with a stone, the ring should be completely cold and boil in the alum cup to remove the residual boric acid and other impurities. Do not put the ring into cold water at high temperature, otherwise the stones will cause a cold burst. The above is the modification method of the ring mouth.
Generally speaking, it is easier to change the ring. As long as the original ring circles are cut off the excess part, and the two sections can be welded; and the ring is relatively complicated. Some can achieve the purpose through the beating. Some must cut the original ring ring, and then add a precious metal material of the same material. If the ring to change the ring, find the right place on the ring, then add gold or cut gold, and finally weld the ring and polish (of course, the shape must be maintained). This method of changing the size is suitable for a ring with relatively simple structure and no special materials, and the number of modified numbers in a certain range, like Bulgari's spring ring Note that it is not suitable for modification. Some rings are limited by materials or inlaids, and they cannot be adjusted at will.
This rings contain special materials, such as some spring rings and Cartier three -color gold rings. This ring cannot be changed in this method. Pucting information: The common ring mouth size of various rings The human cards are generally between No. 4 and 26. Most of the women's rings are No. 1 to No. 1 to No. 1, of which No. 1 2 and 13 are more common. Men's rings are mostly No. 17 -22, of which 18, 19 and 20 are more common. The ring slogan is the perimeter of the ring in the ring of the ring, also known as the inch, and the unit is represented by millimeter (mm). The national standard GB/T11888 "Definition, Survey and Naming of Jewelry Ring Dimensions" has made detailed provisions on the size of the ring. The measured ring length should be performed with a tapered ring section. The effective range length of the volume regulation is (1 60 soil 0.5) mm. The smallest ring size is 41 mm, and the maximum ring size is 76 mm. The ring size is represented by the closest scale value of the IS () 8653 and the perimeter of the ring in the ring. If the measured ring length is 43 mm, the expression is: Ring-Size IS0 8653-43.
If you change the inch, cut the ring ring ring, and then add a certain amount of gold (or platinum, etc. to the interface, depend on your ring material), and then combine the two ends. There are traces of changes, but some styles of ring can be changed, some are not good, generally modified in 3-4 circles
If it is changed from childhood, then the ductility of gold is used directly. If it is changed from a large change, then cut it, cut off a section, and then welded.
Golding method is changed
The gold method is a commonly used ring to change the large -sized method. The specific operation method is to cut the ring ring, add the same precious metal material, and then weld. After the welding is completed, the welding site should be polished and renovated to eliminate welding marks. Although the Gold Method is commonly used, the Gold Method is suitable for some rings with a single trash, no pattern, no more decorative ring.
The gold cutting method to small
The gold cutting method can be changed to small rings size, cut off a short section of the ring, then welded the ring, then polished and refurbished. , Eliminate welding marks. The gold cutting method is also suitable for some rings of the trash, with no pattern and no more decorative ring.
This ring method changes to small
This can also change small size. According to the size of the inner wall of the ring, make a cushion embedded on the inner wall of the ring, and the pads will reduce the ring to reduce the ring. The role of size. The padding method is suitable for all rings to change small size. The padding method has the least harm to the ring. If the ring is small, you can remove the ring of the ring to make the ring larger.
The method of modification of the ring tip of the ring is as follows:
1. The center of the bottom of the ring is sawn, and the ring ring on both sides of the fracture is used to cut the ring on both sides of the fracture. In this way, you can ensure that the two sides of the ring circle are opposite.
Is should not cut too much when cutting. After a little cutting, you should use the rings to measure the size of the ring mouth. After cutting, the flap should be slightly larger than the actual need. Use the bamboo leaf cricket to fell smoothly on both sides of the fracture to meet the requirements. At the same time, the smaller the seams at the fracture, the better.
2, take a container, add a little boric acid, and add an appropriate amount of alcohol to completely dissolve boric acid. Put the ring into the boric acid solution.
3, take out the ring in the boric acid solution, use the musket to put the ring hot, and use the tweezers to clamp the sides of the ring ring with the sides of the ring, so that the ring arm on both sides of the ring ring is fitted together. Note: Try to avoid direct heating gems during the heating process.
4. Welded the fracture together to ensure the reliability of welding and avoid forming concave pits, and the amount of welds can be increased in an appropriate amount.
5. After the welding is completed, if it is inlaid with a stone, the ring should be completely cold and boil in the alum cup to remove the residual boric acid and other impurities. Do not put the ring into cold water at high temperature, otherwise the stones will cause a cold burst.
The above is the modification method of the ring mouth.
Generally speaking, it is easier to change the ring. As long as the original ring circles are cut off the excess part, and the two sections can be welded; and the ring is relatively complicated. Some can achieve the purpose through the beating. Some must cut the original ring ring, and then add a precious metal material of the same material.
If the ring to change the ring, find the right place on the ring, then add gold or cut gold, and finally weld the ring and polish (of course, the shape must be maintained). This method of changing the size is suitable for a ring with relatively simple structure and no special materials, and the number of modified numbers in a certain range, like Bulgari's spring ring Note that it is not suitable for modification. Some rings are limited by materials or inlaids, and they cannot be adjusted at will.
This rings contain special materials, such as some spring rings and Cartier three -color gold rings. This ring cannot be changed in this method.
Pucting information:
The common ring mouth size of various rings
The human cards are generally between No. 4 and 26. Most of the women's rings are No. 1 to No. 1 to No. 1, of which No. 1 2 and 13 are more common. Men's rings are mostly No. 17 -22, of which 18, 19 and 20 are more common.
The ring slogan is the perimeter of the ring in the ring of the ring, also known as the inch, and the unit is represented by millimeter (mm). The national standard GB/T11888 "Definition, Survey and Naming of Jewelry Ring Dimensions" has made detailed provisions on the size of the ring. The measured ring length should be performed with a tapered ring section. The effective range length of the volume regulation is (1 60 soil 0.5) mm.
The smallest ring size is 41 mm, and the maximum ring size is 76 mm. The ring size is represented by the closest scale value of the IS () 8653 and the perimeter of the ring in the ring. If the measured ring length is 43 mm, the expression is: Ring-Size IS0 8653-43.
If you change the inch, cut the ring ring ring, and then add a certain amount of gold (or platinum, etc. to the interface, depend on your ring material), and then combine the two ends. There are traces of changes, but some styles of ring can be changed, some are not good, generally modified in 3-4 circles
If it is changed from childhood, then the ductility of gold is used directly. If it is changed from a large change, then cut it, cut off a section, and then welded.